Comtech EF Data CDM-710L Spécifications Page 175
- Page / 242
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
A–1
Appendix A. REMOTE CONTROL
A.1 Overview
This appendix describes the protocol and message command set for remote monitor and control of the CDM-710 Broadcast Satellite
Modem.
The electrical interface is either an EIA-485 multi-drop bus (for the control of many devices) or an EIA-232 connection (for the control of
a single device), and data is transmitted in asynchronous serial form using ASCII characters. Control and status information is transmitted
in packets of variable length in accordance with the structure and protocol defined in later sections.
A.2 EIA-485
For applications where multiple devices are to be monitored and controlled, a full-duplex (or 4-wire) EIA-485 is preferred. Half-duplex (2-
wire) EIA-485 is possible, but is not preferred.
In full-duplex EIA-485 communication there are two separate, isolated, independent differential-mode twisted pairs, each handling serial
data in different directions. It is assumed that there is a ‘Controller’ device (a PC or dumb terminal), which transmits data in a broadcast
mode via one of the pairs. Many ‘Target’ devices are connected to this pair, all of which simultaneously receive data from the Controller.
The Controller is the only device with a line-driver connected to this pair – the Target devices only have line-receivers connected.
In the other direction, on the other pair each Target has a tri-stateable line driver connected, and the Controller has a line-receiver
connected. All the line drivers are held in high-impedance mode until one – and only one – Target transmits back to the Controller.
Each Target has a unique address, and each time the Controller transmits in a framed ‘packet’ of data, the address of the intended recipient
Target is included. All of the Targets receive the packet, but only one – the intended – will reply. The Target enables its output line driver
and transmits its return data packet back to the Controller in the other direction, on the physically separate pair.
- CDM-710 1
- Errata A 3
- Table of Contents 9
- Figures 18
- PREFACE 19
- Preface MN/CDM710.IOM 20
- Installation 21
- Environmental 21
- CE Mark 22
- RoHS Compliance 22
- Warranty Policy 23
- Limitations of Warranty 23
- Exclusive Remedies 24
- Customer Support 25
- Online Customer Support 25
- Chapter 1. INTRODUCTION 27
- 1.2 Functional Description 28
- Introduction MN/CDM710.IOM 29
- 1.3.1 Physical Description 30
- 1.3.2 Major Assemblies 31
- 1.3.3 Dimensional Envelope 32
- 1.3.4 Physical Features 33
- 1.3.4.1 Front Panel 33
- 1.3.4.2 Rear Panel 34
- 1.3.6 Verification 36
- FAST System Theory 37
- FAST Implementation 37
- FAST Accessible Options 37
- Figure 1-7. Spectral Mask 40
- 1.4.2 Modulator 41
- 1.4.2.1 CDM-710 (70/140 MHz 41
- ) Modulator 41
- 1.4.3 Demodulator 42
- Maximum Level 43
- Minimum Level 43
- 1.4.4 Test Functions 45
- 1.4.5 Monitor Functions 45
- 1.4.6 Remote Port Operation 45
- 1.4.7 Data Rate Range 46
- Chapter 2. INSTALLATION 49
- 2.2 Mounting 50
- Installation MN/CDM710.IOM 51
- Chapter 3. REAR PANEL 53
- CONNECTORS 53
- PINOUTS 53
- 3.2.1 Tx IF Connectors, J1 55
- 3.2.2 Rx IF Connectors, J3 55
- 3.4 Utility Connections 56
- 3.4.1 Alarms Connector, P1 56
- 3.5 Power/Ground Connectors 58
- Chapter 4. FLASH UPGRADING 59
- IMPORT ANT 60
- 4.5 USB Procedure 63
- Chapter 5. FRONT PANEL 65
- OPERATION 65
- 5.1.2 Front Panel Keypad 67
- 5.2 Opening Screen 68
- 5.2.1 Menu Matrix 69
- 5.3 SELECT: (Main) Menu 70
- 5.3.1 SELECT: Config 71
- (CONFIG: Remote) Local 72
- (CONFIG: Remote) Serial 72
- (CONFIG: Remote) Ethernet 73
- ENTER when done 74
- (CONFIG: Tx) Mod 76
- (CONFIG: Tx:) Mod Æ Type 76
- (CONFIG:Tx) Mod Æ Inv 76
- (CONFIG: Tx) Mod Æ α 77
- (CONFIG: Tx) Code 78
- (CONFIG : Tx) SymRate 78
- (CONFIG: Tx) Mode 80
- (CONFIG: Tx) Frequency 81
- (CONFIG: Tx) Pwr 81
- (CONFIG: Tx) Pwr Æ Level 82
- (CONFIG: Tx) Pwr Æ On/Off 82
- (CONFIG: Tx) Pwr Æ Imped 82
- 5.3.1.3 (CONFIG:) Rx 83
- (CONFIG: Rx) FEC 83
- (CONFIG: Rx) Dem (Demod) 83
- (CONFIG: Rx) Dem Æ Type 83
- (CONFIG: Rx) Dem Æ Inv 84
- (CONFIG: Rx) Dem Æ Acq 84
- (CONFIG: Rx) Dem Æ α 84
- (CONFIG: Rx) Dem Æ Eq 84
- (CONFIG: Rx) Dem Æ IQ-TP 85
- (CONFIG: Rx) Code 85
- (CONFIG: Rx) SymRate 86
- (CONFIG: Rx) Mode 86
- (CONFIG: Rx) Freq 86
- (CONFIG: Rx) Eb/No 87
- (CONFIG: Rx) PLL 87
- Interface 2 88
- (CONFIG: Intfc1 ASI) Config 89
- (CONFIG: Intfc1 HSSI) Tx 90
- ENTER 93
- • Normal: CTS = RTS 93
- ENTER. Enable is selected to 97
- ENTER. Enable is 97
- ENTER or CLEAR when done 99
- 5.3.1.7 (CONFIG:) Ref 101
- 5.3.1.8 (CONFIG:) Aux 101
- (CONFIG: Aux) Auto/Manual 101
- (CONFIG: Aux) Ena/Dis 102
- (CONFIG: Aux) FORCE(1:1) 102
- 5.3.1.9 (CONFIG:) Alarms 102
- (CONFIG: Alarms) Tx 102
- 5.3.2 SELECT: Monitor 103
- 5.3.2.1 (Monitor:) Alarms 103
- (Monitor: Alarms) Transmit 103
- (CONFIG: Alarms) Intfc1 103
- (Monitor: Alarms) Receive 104
- (Monitor: Alarms) Unit 104
- 5.3.2.2 (Monitor:) Rx_Stats 106
- (Monitor:) Event-Log Æ View 107
- 5.3.3 SELECT: Test 107
- 5.3.3.1 (Test:) Mode 107
- (Available Some Interfaces) 109
- 5.3.4 SELECT: Info 110
- 5.3.4.1 (INFO:) Rem 110
- 5.3.4.2 (INFO:) Tx 111
- 5.3.4.3 (INFO:) Rx 111
- 5.3.5 SELECT: Save/Load 113
- 5.3.5.1 (Save/Load:) Save 113
- 5.3.5.2 (Save/Load:) Load 114
- 5.3.6.1 (UTIL:) RT-Clk 114
- 5.3.6.2 (UTIL:) Ref 115
- 5.3.6.3 (UTIL:) ID 115
- 5.3.6.4 (UTIL:) Display 115
- 5.3.6.5 (UTIL:) Firmware 115
- (Firmware:) Info 116
- (Firmware:) Info Æ Bootrom 116
- (Firmware:) Select 116
- 5.3.6.6 (UTIL:) FAST 118
- (FAST:) Cnfg (Configuration) 118
- (FAST:) Cnfg Æ Code 118
- (FAST:) Cnfg Æ Demo Mode 118
- (UTIL:) FAST Æ View 119
- Chapter 6. ETHERNET 121
- MANAGEMENT 121
- IMPORTANT 122
- 6.3.1.1 Common Private MIBs 123
- 6.3.1.3 ASI Private MIB 123
- 6.3.1.6 HSSI MIB 124
- 6.3.3 SNMP Traps 124
- 6.4 Telnet Interface 125
- 6.4.2 Using Telnet 127
- 6.4.3 Telnet Examples 127
- 6.5.2 User Login 128
- 6.5.3 Web Server Menu Tree 129
- 6.5.4.1 Home Page 130
- Select Boot Image 139
- Perform Soft Reboot 139
- Chapter 7. FORWARD ERROR 145
- CORRECTION OPTIONS 145
- 7.3.1 Range of Data Rates 146
- Eb/No (dB) 150
- DVB-S: QPSK BER vs Eb/No 150
- Es/No (dB) 153
- DVB-S2: 8-PSK PER vs Es/No 154
- Chapter 8. CDI-40 ASI 157
- INTERFACE MODULE 157
- 8.2.1 Connector Pinouts 159
- 8.3 Functional Description 160
- 8.3.1.1 MPEG-2 Null Packet 160
- 8.3.3 1:1 Applications 161
- 8.4 General Specifications 162
- Chapter 9. CDI-60 HSSI 163
- 9.2 Physical Description 164
- 9.2.1 Connector Pinout 165
- Continuous Clock 166
- Gap Clock 166
- GIGABIT ETHERNET (GigE) 167
- Gigabit Ethernet Card 168
- MPEG COP3 Annex A) 170
- Appendix A. REMOTE CONTROL 175
- A.3 EIA-232 176
- A.4 Basic Protocol 176
- A.5.3 Address Delimiter 178
- A.5.4 Instruction Code 178
- A.5.7 End Of Packet 179
- Appendix A MN/CDM710.IOM 180
- A–6 180
- A.6.1 Modulator 181
- A–8 182
- A–9 183
- A–10 184
- A–11 185
- A–12 186
- A–13 187
- A–14 188
- A–15 189
- A–16 190
- A–17 191
- A–18 192
- A–19 193
- A.6.2 Demodulator 194
- A–21 195
- A–22 196
- A–23 197
- A–24 198
- A–25 199
- A–26 200
- A–27 201
- A–28 202
- N/A 5 bytes Query only 203
- A–30 204
- A–31 205
- A–32 206
- A.6.3 Modem 207
- A–34 208
- A–35 209
- A–36 210
- A.6.4 Priority System 211
- A–38 212
- A–39 213
- A–40 214
- A–41 215
- A–42 216
- A–43 217
- A–44 218
- A–45 219
- A–46 220
- A–48 222
- A–49 223
- A–50 224
- A–51 225
- A.6.5.1 MGC Format 226
- A–53 227
- A–54 228
- A–55 229
- A–56 230
- Appendix B. Eb/No 231
- MEASUREMENT 231
- ((Co+No)/No)/10) 232
- Appendix C. FAST ACTIVATION 237
- PROCEDURE 237
- UTILITY Æ FAST menu: 239
- Cnfg, then press [ENTER]: 239
- C.3 Using FAST Demo Mode 240
- METRIC CONVERSIONS 241
- Units of Length 241
- Temperature Conversions 241
- Units of Weight 241
- 480 • 333 • 2200 PHONE 242
- • 333 • 2161 FAX 242
Produits connexes et manuels pour Mise en réseau Comtech EF Data CDM-710L
Whirlpool WFC9820HW manuals
Owner’s manuals and user’s guides for Washing machines Whirlpool WFC9820HW.
We providing 2 pdf manuals Whirlpool WFC9820HW for download free by document types: Use and Care Manual, Quick Start Guide
Whirlpool WFC9820HW Use and Care Manual (36 pages)
Brand: Whirlpool | Category: Washing machines | Size: 4.08 MB |
Table of contents
Whirlpool WFC9820HW Quick Start Guide (2 pages)
Brand: Whirlpool | Category: Washing machines | Size: 1.59 MB |
Table of contents
More products and manuals for Washing machines Whirlpool
| Models | Document Type |
|---|---|
| WFW5090GW |
Installation Manual
Whirlpool WFW5090GW Installation Instruction,
72 pages
|
| WTW8700EC |
Use and Care Manual
Whirlpool WTW8700EC WTW8700EC Use and Care EN,
28 pages
|
| WET4024HW |
User's Guide
Whirlpool WET4024HW User Guide [et] [it] [lv] ,
56 pages
|
| WFW3090GW |
Installation Manual
Whirlpool WFW3090GW Installation Instructions,
72 pages
|
| WTW8500DW |
Installation Guide
Whirlpool WTW8500DW Installation Guide,
16 pages
|
| WTW7000DW |
Use and Care Guide
Whirlpool WTW8000DW Use & Care Guide,
44 pages
|
| WFW9620HW |
Use and Care Guide
Whirlpool WFW9620HW Use and Care Guide,
74 pages
|
| WTW4950HW |
Use and Care Manual
Whirlpool WTW4950HW Use and Care,
36 pages
|
| WTW7500GW |
Installation Manual
Whirlpool WTW5000DW Installation Instructions,
16 pages
|
| WTW4616FW |
Installation Manual
Whirlpool WTW4616FW Installation Instruction,
16 pages
|
| WFW5090GW |
Use and Care Manual
Whirlpool WFW5090GW Use and Care,
72 pages
|
| WFW560CHW |
Use and Care Manual
Whirlpool WFW560CHW Use and Care,
71 pages
|
| WTW4955HW |
Installation Guide
Whirlpool WTW4955HW Installation guide,
16 pages
|
| WTW4616FW |
Use and Care Manual
Whirlpool WTW4616FW Use and Care,
36 pages
|
© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels