Comtech EF Data UT-4518E Spécifications Page 39
- Page / 132
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2–1
Chapter 2. INSTALLATION
2.1 Unpacking and Inspection
The UT-4500-A Series Upconverter and its Installation and Operation Manual are packaged and
shipped in a pre-formed, reusable cardboard carton containing foam spacing for maximum
shipping protection.
Inspect shipping containers for damage. If shipping containers are damaged, keep them until the
contents of the shipment have been carefully inspected and checked for normal operation.
CAUTION
Do not use any cutting tool that will extend more than 1” into the container
and cause damage to the converter.
Unpack and inspect the UT-4500-A Series Upconverter as follows:
Step Procedure
1
Cut the tape at the top of the carton indicated by OPEN THIS END.
2
Remove the cardboard/foam space covering the converter.
3
Remove the upconverter, manual, and power cord from the carton.
4
Save the packing material for storage or reshipment purposes.
5
Inspect the equipment for any possible damage incurred during shipment.
6
Check the equipment against the packing list to ensure the shipment is correct.
7
Refer to the next section (Section 2.2) for installation instructions.
CAUTION
The equipment contains parts and assemblies sensitive to damage by Electrostatic
Discharge (ESD). Use ESD precautionary procedures when touching, removing, or
inserting the up/downconverter modules.
- UT-4500-A Series 1
- Errata A 3
- TABLE OF CONTENTS 7
- FIGURES 14
- PREFACE 15
- Preface MN-UT4500A 16
- Warranty Policy 18
- Limitations of Warranty 18
- Exclusive Remedies 19
- Customer Support 20
- Online Customer Support 20
- Chapter 1. INTRODUCTION 21
- 1.2 Features 22
- 1.2.2 Dimensional Envelope 23
- 1.2.3 Front Panel 24
- 1.2.4 Rear Panel 24
- 1.3 Theory of Operation 25
- 1.3.1 Applications 25
- 1.3.2 RF Signal Conversion 26
- 1.3.3 Monitor & Control 27
- Introduction MN-UT4500A 28
- Chapter 2. INSTALLATION 39
- 2.2 Installation 40
- Installation MN-UT4500A 41
- 2.4 Connect External Cables 43
- Chapter 3. REAR PANEL 45
- CONNECTORS 45
- IMPORTANT 46
- IMPORTAN 47
- 3.3 Cable Connections 53
- Module (TSM-XX) Installed 55
- Chapter 4. FLASH UPGRADING 57
- Flash Upgrading MN-UT4500A 58
- Chapter 5. FRONT PANEL 63
- OPERATION 63
- 5.1.2 LED Indicators 64
- 5.1.3 Keypad 65
- 5.2 Opening Screen 66
- 5.3 Main Menu 66
- 5.3.1.1 CONFIG: OUTPUT 67
- 5.3.1.3 CONFIG: REDUNDANCY 71
- 5.3.1.5 CONFIG: COLDSTART 73
- 5.3.2 MONITOR 74
- 5.3.3 FAULTS 74
- 5.3.3.1 FAULTS: CURRENT 74
- 5.3.4 PRE-SELECTS 75
- 5.3.4.1 PRE-SELECTS: LOAD 76
- 5.3.4.3 PRE-SELECTS: CLEAR 76
- 5.3.5 UTILITY 77
- 5.3.5.5 UTILITY: SLOPE 78
- 5.3.5.6 UTILITY: LAMP-TEST 79
- 5.3.5.7 UTILITY: FIRMWARE 79
- MANAGEMENT 81
- Chapter 6. ETHERNET 81
- 6.3.3 SNMP Traps 83
- 6.4 Telnet Interface 84
- Appendix A. REMOTE CONTROL 87
- A.2.2 TIA/EIA-232 (RS-232) 88
- A.2.3 Ethernet (100BASE-TX) 88
- A.3 Access Methods 88
- A.3.1 Direct Access 88
- A.3.2 Indirect Access 89
- A.4 Addresses 89
- A.4.1 Physical Address 89
- A.4.2 Virtual Address 89
- A.6 Message Structure 91
- A.6.1 Start Character 91
- A.6.2 Device Address 91
- A.6.3 Command 91
- A.6.4 Confirmation Response 92
- A.6.5 Error Response 92
- A.6.6 End of Message 92
- A.6.6.1 Command Ending 92
- A.6.6.2 Response Ending 92
- A.7.1 Utility Commands 93
- A.7.1.1 Time 93
- A.7.1.2 Date 93
- A.7.1.5 IP Address 94
- A.7.1.6 IP Gateway 94
- A.7.1.7 Physical Address 95
- A.7.1.8 Baud Rate 95
- A.7.1.9 LCD Contrast 95
- A.7.1.10 LCD Brightness 95
- A.7.1.11 Screen Saver Mode 96
- A.7.1.13 VFD Brightness 96
- A.7.1.16 Equipment Type 97
- A.7.1.17 Part Number 97
- A.7.1.20 Firmware Image 98
- A.7.1.22 Force Reboot 99
- A.7.2.1 Frequency 99
- A.7.2.2 Attenuator 99
- A.7.2.3 Cold Start 100
- A.7.2.4 Mute 100
- A.7.2.5 Carrier Mute Mode 100
- A.7.2.6 Redundant Mute Mode 100
- A.7.2.7 Auto Fault Recovery 101
- A.7.2.8 Program Preset 101
- A.7.2.9 Display All Presets 101
- A.7.3.1 Redundant Mode 102
- A.7.3 Modes 102
- A.7.3.3 Backup Mode 103
- A.7.4 Status Commands 104
- A.7.4.2 Maintenance Status 104
- A.7.4.3 Utility Status 105
- A.7.4.4 Alarm Status 105
- Command Details 106
- Appendix A MN-UT4500A 107
- A.7.5 Stored Alarms 108
- A.7.5.1 Total Stored Alarms 108
- A.7.5.3 List All Alarms 108
- A.7.6 Error Processing 109
- A.7.6.1 General Errors 109
- A.7.6.3 Mode Errors 109
- A.7.6.4 Time-Outs 109
- A.7.7 Command Summaries 110
- Appendix B. REDUNDANT 113
- SYSTEM OPERATION 113
- B.2.2 Detachable Modules 114
- Installed 115
- TSEQM-XX Installed 116
- TSM-XX Installed 117
- Appendix B MN-UT4500A 118
- B.4.1 Initial Configuration 120
- adjusted to minimize 125
- Appendix C. MAINTENANCE AND 127
- TROUBLESHOOTING 127
- Appendix C MN-UT4500A 128
- C.2.3.3 RF Converter Module 129
- C.2.3.7 Temperature Fault 129
- C.2.4 Converter I/O Modules 130
- C.3 Spares 130
- METRIC CONVERSIONS 131
- Units of Length 131
- Temperature Conversions 131
- Units of Weight 131
- 480 • 333 • 2200 PHONE 132
- • 333 • 2161 FAX 132
Produits connexes et manuels pour Non Comtech EF Data UT-4518E
Non Comtech EF Data KST-2000B Spécifications
(184 pages)
(184 pages)
Non Comtech EF Data MBT-4000 Spécifications
(78 pages)
(78 pages)
Non Comtech EF Data KST-2000A Spécifications
(182 pages)
(182 pages)
Non Comtech EF Data UT-4514F Spécifications
(162 pages)
(162 pages)
Non Comtech EF Data MBT-4000B Spécifications
(88 pages)
(88 pages)
Non Comtech EF Data CIC-50 Spécifications
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels