Comtech EF Data UT-4518E Spécifications Page 71
- Page / 112
- Table des matières
- MARQUE LIVRES
- UT-4500 Series 1
- Errata A 3
- Filename: T_ERRATA 2 4
- Errata B 5
- Redundant operation 6
- CUSTOMER SUPPORT 8
- Table of Contents 9
- Preface Revision 2 10
- Figures 13
- ABOUT THIS MANUAL 15
- CONVENTIONS AND REFERENCES 15
- METRIC CONVERSION 15
- TRADEMARKS 15
- EMC COMPLIANCE 16
- SAFETY COMPLIANCE 17
- EN 60950 17
- WARRANTY POLICY 18
- Chapter 1. Introduction 19
- 1.2 FUNCTIONAL DESCRIPTION 20
- Introduction Revision 2 21
- 1.3 SPECIFICATIONS 22
- 1.4 PHYSICAL CONFIGURATION 33
- 1.5 FRONT PANEL DISPLAY 34
- 1.7 PRIME POWER SWITCH 34
- 1.8 NEW IN THIS MANUAL 34
- Chapter 2. Installation 37
- 2.4 CABLE CONNECTIONS 38
- Installation Revision 2 39
- UP CONVERTER - TSM 42
- Chapter 3. System Operation 43
- UT_4514-1 44
- SW VER 4.06 SN45143513 44
- 3.2 SWITCHING POWER ON 45
- 3.3 OPERATION 45
- ---------SELECT 46
- --CURRENT-FAULTS-MENU 46
- --MONITOR-STATUS-MENU 47
- ----CONFIGURATION-MENU 48
- ---MONITOR-STATUS-MENU 50
- ---CURRENT-FAULTS-MENU 51
- -UTILITY-FUNCTIONS-MENU 52
- 3.3.1 CONVERTER COMMANDS 53
- System Operation Revision 2 54
- 3.3.7 UTILITY FUNCTION MENU 57
- Chapter 4 59
- Redundant System Operation 59
- 4.2 BACKUP CONVERTER 60
- 4.3 REDUNDANT CONFIGURATIONS 61
- Remote Control Revision 2 62
- Up Converter - IOM 63
- (Backup Unit) 63
- Up Converter - TSEQM 63
- (On line) 63
- 4.4.1 INITIAL CONFIGURATION 67
- CONV-01-OFFSET=+00.00-DB 69
- REDUNDANCY-CONFIG?-ON 69
- -CONVERTER-#-02 69
- -CONVERTER-#-03 69
- -ACTIVATE-BACKUP:-FORCED 71
- 4.4.4 OFFSET ADJUSTMENT 72
- Chapter 5 75
- Remote Control 75
- 5.2.2 BAUD RATE 76
- 5.2.3 FORMAT 76
- 5.2.4 CHARACTER SET 76
- 5.2.5 RESPONSE TIMEOUT 76
- 5.3 ACCESS METHODS 77
- 5.4 ADDRESSES 78
- 5.5 MESSAGE STRUCTURE 79
- 5.5.5 ERROR RESPONSE 80
- 5.5.6 END OF MESSAGE 80
- 5.5.6.1 COMMAND ENDING 80
- 5.5.6.2 RESPONSE ENDING 80
- 5.6 COMMAND / RESPONSE PAIRS 81
- 5.6.1.5 LCD CONTRAST 82
- 5.6.1.6 LCD BRIGHTNESS 82
- 5.6.1.9 EQUIPMENT TYPE 83
- 5.6.2 CONFIGURATION COMMANDS 84
- 5.6.2.1 F 84
- 5.6.2.2 ATTENUATOR 85
- 5.6.2.3 COLD START 85
- 5.6.2.4 MUTE 85
- 5.6.2.5 AUTO FAULT RECOVERY 86
- 5.6.2.6 PROGRAM PRESET 86
- 5.6.2.7 DISPLAY ALL PRESETS 86
- 5.6.2.8 CLEAR PRESET 87
- 5.6.2.9 SELECT A PRESET 87
- 5.6.3 MODES 87
- 5.6.3.1 REDUNDANCY MODE 87
- UTOMATIC/MANUAL MODE 88
- 5.6.3.3 BACKUP MODE 89
- 5.6.4 STATUS COMMANDS 89
- 5.6.4.1 CONFIGURATION STATUS 89
- 5.6.4.2 MAINTENANCE STATUS 90
- 5.6.4.3 UTILITY STATUS 90
- 5.6.4.4 ALARM STATUS 90
- 5.6.4.5 SUMMARY ALARM STATUS 91
- ACKED MAINTENANCE STATUS 92
- ACKED UTILITY STATUS 92
- 5.6.4.10 PACKED ALARM STATUS 93
- 5.6.5 STORED ALARM 93
- 5.6.5.1 TOTAL STORED ALARMS 93
- 5.6.5.3 LIST ALL ALARMS 94
- 5.7 ERROR PROCESSING 95
- Chapter 6 99
- Theory of Operation 99
- 6.2 RF SIGNAL CONVERSION 100
- IF INPUT 101
- (70 or 140 MHz) 101
- RF OUTPUT 101
- (14000-14500 MHz) 101
- 6.3 MONITOR & CONTROL 102
- Chapter 7 103
- 7.2 MAINTENANCE TESTING 104
- 7.2.2 TROUBLESHOOTING 105
- 7.2.3 CONVERTER FAULTS 105
- 7.2.3.1 PRIME POWER 105
- 7.2.3.3 RF CONVERTER MODULE 106
- 7.2.3.7 TEMPERATURE FAULT 106
- 7.3 SPARE 107
- Index Revision 2 110
- METRIC CONVERSIONS 111
- Units of Length 111
- Temperature Conversions 111
- Units of Weight 111
- 480 • 333 • 2200 Phone 112
- 480 • 333 • 2161 FAX 112
© 2020, manymanuals.fr. Tous droits réservés | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels