Comtech EF Data SDM-309B Spécifications Page 113
- Page / 240
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
M&C and Interfaces SDM-309B Satellite Modem
4-4–36 MN/U-SDM309B Rev. #
4.2.2.10.1 Drop Data Input, Insert Data Output, and Ext. Ref Clk (J1)
The Drop Data Input, Insert Data Output, and External Reference Clock balanced signals
are provided on a 15 pin “D” female connector accessible from the front of the break-out
panel. Screw locks are provided for mechanical security of the mating connector.
Signal Function Name Pin Number
GROUND GND 2, 4
INSERT DATA OUT IDO-A
IDO-B
3
11
EXTERNAL CLOCK EXC-A
EXC-B
7
8
DROP DATA INPUT DDI-A
DDI-B
1
9
Note: The balanced insert data output signals on J1 are selected by SW2. The balanced
drop data input signals on J1 are selected by SW1. The balanced External Clock signals
on J1 are selected by SW3. Refer to Section 4.2.2.11 for further rear panel switch
information.
4.2.2.10.2 Drop Data Output (J2)
The balanced Drop Data Output signals are provided on a 15 pin “D” female connector
accessible from the front of the breakout panel. Screw locks are provided for mechanical
security of the mating connector.
Signal Function Name Pin Number
GROUND GND 2, 4
DROP DATA OUTPUT DDO-A
DDO-B
1
9
DROP DATA OUTPUT DDO-A
DDO-B
3
11
Note: The drop data output signals are connected to SW5 which selects DTE or DCE
operation. Refer to Section 4.2.2.11.7 for further information on SW5. The balanced
drop data output signals on J2 are selected by SW1. Refer to Section 4.2.2.11.2 for
further balanced drop data output selection.
4.2.2.10.3 Insert Data Input (J3)
The balanced Insert Data Input is provided on a 15 pin “D” female connector assessable
from the front panel of the breakout panel. Screw locks are provided for mechanical
security of the mating connector.
Signal Function Name Pin Number
GROUND GND 2, 4
INSERT DATA INPUT IDI-A
IDI-B
3
11
- SDM-309B 1
- SDM-309BSDM-309B 1
- Warranty Policy 3
- Limitations of Warranty 3
- Exclusive Remedies 3
- Disclaimer 3
- About this Manual 4
- Cautions and Warnings 4
- Metric Conversion 4
- Trademarks 5
- Customer Support 6
- Table of Contents 8
- Rev. 0 vii 10
- Rev. 0 ix 12
- Chapter 1 14
- INTRODUCTION 14
- 1-1–2 MN/U-SDM309B Rev. # 15
- Figure 1-1 SDM-309B Modem 16
- 1-1–4 MN/U-SDM309B Rev. # 17
- MN/U-SDM309B Rev. # 1-1–5 18
- 1-1–6 MN/U-SDM309B Rev. # 19
- 1.4 System Specification 20
- 1-1–10 MN/U-SDM309B Rev. # 23
- MN/U-SDM309B Rev. # 1-1–11 24
- 1-1–12 MN/U-SDM309B Rev. # 25
- Chapter 2 26
- INSTALLATION 26
- Figure 2-1 Rear Panel View 28
- 2.2.1 Data I/O 29
- 2.2.2 Remote (J6) 29
- 2.2.3 Fault (J7) 29
- 2.2.4 IF Output (CP1) 30
- 2.2.5 IF Input (CP2) 30
- 2.2.6 AC Power 30
- 2.2.7 GND 30
- 2.3 System Requirements 30
- 2.4 System Installation 31
- Chapter 3 32
- OPERATION 32
- 3.1.3 Front Panel Controls 33
- Figure 3-1 Front Panel View 34
- 3.1.4 Configuration 35
- 3.1.4.1 MOD Configuration 35
- 3.1.4.2 DEMOD Configuration 36
- 3.1.5 Monitor 41
- 3.1.6 Faults 41
- 3.1.7 Stored Faults 43
- 3.1.8 Utility 43
- Figure 3-2 Menu Tree 47
- Figure 3-3 Menu Tree 48
- Figure 3-4 Menu Tree 49
- Figure 3-5 Menu Tree 50
- Figure 3-6 Menu Tree 51
- Figure 3-7 Menu Tree 52
- Figure 3-8 IF Loopback 53
- Figure 3-9 RF Loopback 54
- 3–24 MN/U-SDM309B Rev. # 55
- MN/U-SDM309B Rev. # 3–25 56
- 3.2.1 General 57
- 3.2.2 Configuration 57
- 3.2.2.1 MOD Configuration 58
- 3.2.2.2 DEMOD Configuration 59
- 3.2.3 Monitor 65
- 3.2.4 Faults 66
- 3.2.5 Stored Faults 67
- 3.2.6 Utility 68
- Figure 3-12 Menu Tree 71
- Figure 3-13 Menu Tree 72
- Figure 3-14 Menu Tree 73
- Figure 3-15 Menu Tree 74
- Figure 3-16 Menu Tree 75
- Figure 3-17 Menu Tree 76
- 3–46 MN/U-SDM309B Rev. # 77
- Chapter 4 78
- M&C AND INTERFACES 78
- Connect JP7 to RS232 79
- MN/U-SDM309B Rev. # 4-4–3 80
- 4.1.2.2 Remote Baud Rate 81
- 4.1.2.3 Remote Address 81
- 4.1.2.4 Battery 81
- 4.1.2.8 Utility Defaults 83
- 4.2 Digital Interfaces 83
- 4.2.1 IBS/M1200P Interface 84
- 4.2.1.2 Data Interface 84
- 4.2.1.3 Transmit Multiplexer 84
- 4-4–8 MN/U-SDM309B Rev. # 85
- MN/U-SDM309B Rev. # 4-4–9 86
- 4-4–10 MN/U-SDM309B Rev. # 87
- Figure 4-4 IBS Fault Tree 88
- Figure 4-5 Jumper Table 89
- 4.2.1.4 Receive Multiplexer 90
- 4-4–18 MN/U-SDM309B Rev. # 95
- 4.2.1.9.7 Send Data (J7) 98
- 4.2.1.9.8 Receive Data (J8) 99
- MN/U-SDM309B Rev. # 4-4–23 100
- 4-4–24 MN/U-SDM309B Rev. # 101
- 4.2.2.2 Data Interface 102
- 4.2.2.3 Transmit Multiplexer 102
- 4.2.2.7 Backward Alarm 103
- MN/U-SDM309B Rev. # 4-4–27 104
- 4-4–28 MN/U-SDM309B Rev. # 105
- MN/U-SDM309B Rev. # 4-4–29 106
- 4-4–30 MN/U-SDM309B Rev. # 107
- MN/U-SDM309B Rev. # 4-4–31 108
- MN/U-SDM309B Rev. # 4-4–35 112
- 4.2.2.10.11 Faults (J11) 115
- 4.2.2.11 Rear Panel Switches 116
- 4.2.2.11.1 Drop Data Input 116
- 4.2.2.11.2 Drop Data Output 116
- 4.2.2.11.3 Insert Data Input 116
- 4-4–40 MN/U-SDM309B Rev. # 117
- MN/U-SDM309B Rev. # 4-4–41 118
- Table 4-3 119
- MN/U-SDM309B Rev. # 4-4–43 120
- 4-4–44 MN/U-SDM309B Rev. # 121
- 4.3.1 Master/Slave 122
- 4.3.1.2 Master/Slave G.703 123
- 4.3.1.3 Master/Slave X.21 123
- 4.3.2 Master/Master 123
- Chapter 5 125
- THEORY OF OPERATION 125
- Figure 5-1 Modulator Card 127
- 5-5–4 MN/U-SDM309B Rev. # 128
- MN/U-SDM309B Rev. # 5-5–5 129
- 5.1.3 Theory of Operation 130
- 5.2.1 General Description 131
- MN/U-SDM309B Rev. # 5-5–9 133
- 5-5–10 MN/U-SDM309B Rev. # 134
- MN/U-SDM309B Rev. # 5-5–11 135
- 5-5–12 MN/U-SDM309B Rev. # 136
- MN/U-SDM309B Rev. # 5-5–13 137
- 5.2.3 Theory Of Operation 138
- 5.2.3.1 Demod Processor 138
- 5.2.3.2 Viterbi Decoder 138
- 5.3 Demodulator 139
- 5.3.1 General Description 139
- 5.3.2 Specifications 140
- Figure 5-9 Demodulator Card 141
- 5-5–18 MN/U-SDM309B Rev. # 142
- 5.3.3 Theory of Operation 143
- 5.4.1 General 143
- 5.4.2 Reacquisition 144
- 5.4.3 Fast Acquisition 145
- 5.4.4 Directed Sweep 145
- Chapter 6 146
- MAINTENANCE 146
- 6-6–2 MN/U-SDM309B Rev. # 147
- MN/U-SDM309B Rev. # 6-6–3 148
- 6-6–4 MN/U-SDM309B Rev. # 149
- Table 6-1 150
- 6-6–6 MN/U-SDM309B Rev. # 151
- MN/U-SDM309B Rev. # 6-6–7 152
- 6.1.4 Test Points 153
- Figure 6-6 154
- Figure 6-7 155
- Figure 6-8 156
- Figure 6-9 157
- 6.2 Fault Isolation 158
- 6.2.1 Modulator Faults 158
- 6.2.2 Demodulator Faults 159
- Table 6-2 162
- 6-6–18 MN/U-SDM309B Rev. # 163
- MN/U-SDM309B Rev. # 6-6–19 164
- 6-6–20 MN/U-SDM309B Rev. # 165
- MN/U-SDM309B Rev. # 6-6–21 166
- 6.4 Module Replacement 167
- 6.5 Module Identification 167
- 6.6 Repacking For Shipment 167
- Table 6-3 168
- Appendix A 169
- DATA RATES AND FILTERS 169
- 1.2 Variable Rate Filters 170
- MN/U-SDM309B Rev. # A–3 171
- A–4 MN/U-SDM309B Rev. # 172
- MN/U-SDM309B Rev. # A–5 173
- A–6 MN/U-SDM309B Rev. # 174
- MN/U-SDM309B Rev. # A–7 175
- A–8 MN/U-SDM309B Rev. # 176
- MN/U-SDM309B Rev. # A–9 177
- Appendix B 178
- SATELLITE MODEM REMOTE 178
- 3.4 End Character 179
- 3.1 Start Character 179
- 3.2 Device Address 179
- 3.3 Command/Responses 179
- 4.2.2 Demodulator Rate 183
- 4.2.4 RF Loop-back (ON/OFF) 184
- 4.2.5 IF Loop-back (ON/OFF) 184
- 4.2.7 Sweep Reacquisition 185
- 4.2.8 Fast Acquisition Mode 185
- 4.2.9 Sweep Center Frequency 185
- 4.2.10 Sweep Width Range 186
- 4.2.11 Sweep Direction 186
- 4.3.12 Interface Buffer Size 188
- 4.3.13 Transmit Data Fault 189
- 4.3.14 Receive Data Fault 189
- 4.3.15 Drop Data Format 189
- 4.3.16 Insert Data Format 189
- 4.4.1 Time Of Day 191
- 4.4.2 Date 191
- 5.3 Modulator Status 195
- 5.4 Demodulator Status 195
- 5.5 Common Equipment Status 196
- 5.8 Bit Error Rate Status 197
- 5.8.1 Raw BER 197
- 5.8.2 Corrected BER 197
- 5.8.3 Corrected BER Log 197
- 5.9 Eb/N0 Status 198
- 5.10 Modulator Rate Status 198
- 5.11 Demodulator Rate Status 198
- 5.13 Current Sweep Value 199
- 5.16 Stored Faults 199
- MN/U-SDM309B Rev. # B-B–23 200
- B-B–28 MN/U-SDM309B Rev. # 205
- 5.20 Change Status 206
- 5.21 Equipment Type 206
- B-B–30 MN/U-SDM309B Rev. # 207
- Appendix C 208
- EXTERNAL CHANNEL UNIT 208
- C-C–2 MN/U-SDM309B Rev. # 209
- MN/U-SDM309B Rev. # C-C–3 210
- C-C–4 MN/U-SDM309B Rev. # 211
- MN/U-SDM309B Rev. # C-C–5 212
- C-C–6 MN/U-SDM309B Rev. # 213
- MN/U-SDM309B Rev. # C-C–7 214
- C-C–8 MN/U-SDM309B Rev. # 215
- MN/U-SDM309B Rev. # C-C–9 216
- C-C–10 MN/U-SDM309B Rev. # 217
- 2.0 Digital Interfaces 218
- 2.1.1 Functional Description 218
- C-C–12 MN/U-SDM309B Rev. # 219
- MN/U-SDM309B Rev. # C-C–13 220
- C-C–14 MN/U-SDM309B Rev. # 221
- 2.1.2 Connector Pinouts 223
- 2.1.3 Specification 223
- 2.2 V.35 Interface 224
- 2.2.1 Functional Description 224
- MN/U-SDM309B Rev. # C-C–19 226
- C-C–20 MN/U-SDM309B Rev. # 227
- 2.2.2 Connector Pinouts 228
- 2.2.3 Specification 228
- 3.0 Front Panel Operation 229
- 3.1 Configuration 229
- 3.2 Monitor 232
- 3.3 Faults 232
- 3.4 Stored Faults 233
- 3.5 Utility 233
- Figure C-13 Menu Tree 235
- Figure C-14 Menu Tree 236
- Figure C-15 Menu Tree 237
- MN/U-SDM309B Rev. # C-C–31 238
- Appendix D 239
- SOFTWARE CHANGE 239
- SPECIFICATIONS 239
Produits connexes et manuels pour Mise en réseau Comtech EF Data SDM-309B
(5 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.115 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels